KERF
العربيةInstall Get Kerf for Fusion
SKETCH CODES The cheat sheet
Watch the 46 shorts →
SKETCH CODES · KERF 2.6

Every sketch code on one page.

Write a code as sketch text inside a cabinet rectangle; it overrides the build dialog for that one cabinet. Words you can remember, with the short codes beside them: every short code you used before still works. Not case-sensitive; separate codes with spaces, commas or new lines.

Download the PDF
WRITTEN INSIDE THE RECTANGLE
720MM 3 SHELF GOLA
KERF READS
  • 720 mm high
  • 3 shelves
  • Gola handle
THE RULES

Four rules, and most codes can be guessed.

With these, most codes can be guessed instead of looked up.

01

A word says what

DRAWERSGLASSGOLASHAKERTOEKICK. The short codes (D, GL, G…) stay as shortcuts.

02

A count goes in front

3 DRAWERS2 DOORS4 SHELF2 LIFT

03

A number glued on is that thing's size

GLASS40GOLA1700SINK740BAR128TOEKICK100

04

A unit is the height, @ is where a floor sits

720MM the cabinet's height; @1450 its floor at 1450; OV600@775 a niche's floor at 775.

And NO in front switches something off: NOGOLANOHANDLENOCOVERSNOFRONTS (short: NG, NH, NMC, NFP).

new a word new in Kerf 2.6kept works as beforeolder still read, a better way exists
01

Interior

8

Shelves, drawers, lift-up leaves, rails and the drawer front panels.

3 SHELF
kept
Shelves, by count.
3 DRAWERSDRAWER
new
3D · D
Wooden drawers; the count goes first.
D150/300/300
kept
Uneven drawers, front heights top-down.
3 ALU3ALU
new
3AD
Aluminium gola drawers.
LIFT2 LIFT
new
LU · 2LU
Lift-up leaf; with N SHELF the shelves go inside.
RAIL2RAIL
kept
Hanging rail / double hanging.
NOFRONTS
new
NFP
Drawer boxes without front panels (FP is the default, no longer taught).
PGHPGH450SL450
kept
Aluminium drawer configuration and slider length (expert codes).
02

Stacked cabinets

6

One form for every multi-part cabinet: sections top to bottom, each in its own bracket.

(1 DOOR GLASS)+(OVEN600@775)+(3 DRAWERS)
kept
(1DR GL)+(OV600@775)+(3D)
A stacked cabinet: sections top to bottom, each bracket with its own codes; a number in a bracket is that section's height, @775 where its floor sits.
(DRAWER 200)+(2 DOORS)
older
1D+2DR
Drawer over doors: the stack says the same, with the drawer's height.
(LIFT)+(LIFT)
older
2LU
Two lift-up leaves over a shelf.
OVENOVEN600MICROWAVE400
kept
OV · MW
An open oven / microwave niche in a stack bracket (600 / 400 mm when no number is given).
|
kept
Parts side by side in a section: (DOOR | DOOR GLASS).
Lines across the rectangle
kept
The same stack drawn: a text per band, the front band at the bottom.
03

Doors & fronts

11

Door count, hinge side, pulls, gola, glass and the door style.

DOOR2 DOORSOPEN
kept
DR · 2DR · 0DR
Door count. Teaching the word avoids 2D (two drawers) vs 2DR (two doors).
LEFTRIGHT
new
HL · HR
The side a single door hinges on.
BARBAR128
new
H · H128
A bar pull (at the standard's / 128 mm centres). H reads like “height”.
KNOB
kept
A knob.
NOHANDLE
new
NH
No pull (push-to-open).
GOLAGOLA1700
kept
G · G1700
Gola channel; glued = the grip line height. Teach the word: G40 vs GL40 is one typo apart.
NOGOLA
new
NG
No gola on this cabinet.
GLASSGLASS40
kept
GL · GL40
Aluminium & glass door (profile width).
SHAKERSLABROUTED
new
DS · DL · DM
Door style. Frees the letter D for drawers.
AROSAMILANOGENEVABOSTONTOKYO
kept
A routed profile (implies ROUTED).
FACEFRAME
new
FF
Face-frame construction.
04

Size & placement

6

Height, wall cabinets, the floor height, the toe kick and board thickness.

720MM72CM30IN
kept
bare 720
Cabinet height. A bare number under 200 is no longer read as a height (see Mistakes).
UPPER
new
UP
Wall cabinet drawn on the floor plan: lifted to 1450 mm. Drawn on a raised plane it stays where it is drawn.
HUNG
new
UH
Wall cabinet hung where it is drawn: for wall cabinets drawn on a sketch plane at their height. The wall-cabinet door (18 mm grip below the carcass), never lifted.
@1450
new
Z1450
The cabinet's floor at 1450: the same @ as in a stack.
TOEKICKTOEKICK100PLINTH
new
TK · TK100
Toe kick under the cabinet.
T18B6
kept
Panel / back thickness (expert codes).
05

Cabinet kinds & appliances

9

These claim the whole rectangle: appliances, towers, the island, panels and fillers.

FRIDGEFRIDGE1920
kept
F
Fridge surround. Teach the word: a stray F turns a cabinet into a fridge surround.
TOWER
new
MO · OM
Oven & microwave tower (a ready-made stack with a ventilation channel).
DISHWASHER
new
DW
Dishwasher space.
SINKSINK740STOVESTOVE OV600
kept
ST · ST750
Sink base, stove base, stove with a built-under oven.
STOVE750STOVE OVEN600
new
ST750 · ST OV600
The number glued onto the word, and the oven word outside a bracket. Both were “no code” before; now read.
HOODISLANDWARDROBEMAGIC
kept
WR
Integrated hood, island, wardrobe, magic corner.
PANELPANEL1200
new
CVR
A solid MDF cover panel.
FILLER
new
SP · SPACER
Corner filler zone.
4 SHELFin an L profile
older
CS4
L-corner shelves: the shape already says corner.
06

Finish & extras

4

Wood, the fronts' colour, MDF covers and the LED slot.

OAKWALNUTMDF…
kept
The whole cabinet's wood, carcass and doors (MDF too: it is no door style).
WHITENAVYSAGE…
kept
The fronts' colour only.
COVERSNOCOVERS
new
MC · NMC
MDF cover panels on / off.
LED
kept
LED slot.
07

Older codes

5

Still read, every one of them. The words are easier to tell apart.

HUNGUH
kept
Draw the wall cabinets on a sketch plane at their height and write HUNG (or UH): a wall cabinet hung where it is drawn. UPPER is the floor-plan way (lifted to 1450).
FP
older
Front panels are the default for drawers; only NOFRONTS is needed.
1D+2DR2LU
older
The stack form says the same (see Stacked cabinets).
CS4
older
4 SHELF inside an L-shaped profile.
DDRDWDS DM DL
kept
Still read; the words are easier to tell apart (2D is two drawers, 2DR two doors).

With Kerf Doors installed, its profile names work as door codes too (for example 101-BeadCove); a profile can never take one of the words on this page.

08

Drawn markers

7

Not text: what you draw inside the rectangle, or the shape you give it.

Construction line
Front to back, inside the rectangle
Splits it into compartments with a full-height divider; codes written in a compartment are that compartment's.
Construction lines across
One per band, a text in each band
A stacked cabinet: the front band is the bottom section; a front-to-back line inside a band splits that section.
Triangle
With a long base
An orientation arrow: its point shows where the front faces.
L-shaped profile
Six corners
A true L corner cabinet.
Two rectangles at 90°
Where two runs meet
A blind corner cabinet (with Auto-detect Corner Cabinets).
Tilted rectangle
Any angle
The cabinet is built turned to match.
Closed construction box
Inside an ISLAND rectangle
The island's carcass; the rest of the rectangle is stone.
09

Room sketch

3

In the room's own sketch (picked in Build Room Shell), never the cabinet sketch.

WINDOW1800x1000
WIN
A window (height × sill, mm) in a box touching the room line.
DOORDOOR1900
A door (height, mm) in a box touching the room line.
CEILING2500WALL120
Ceiling height / wall thickness, anywhere in the room.
MISTAKES

Named instead of built.

What Kerf did before 2.6 and what it does now. A named code shows in Edit Cabinet's preview, in kerf.log and in the finish message (“Sketch codes not used”).

3 DRAWERS
a cabinet 3 mm high; “DRAWERS” is no code
three drawers
D 3
drawers, and a cabinet 3 mm high
“3 ignored: no cabinet is 3 mm high - did you mean 3D?”
GL 40
a glass door, and a cabinet 40 mm high, no warning
“40 ignored: no cabinet is 40 mm high - did you mean GL40?”
G40
a gola line at 40 mm, dropped without a word
“G40 ignored: a gola line at 40 mm is below every door (GL40 is a glass door)”
720MM 760MM
760 mm; the second height wins quietly
720 mm, and “760MM ignored: 720MM came first” (first wins, like every other code)
MDF 2DR
the whole cabinet in MDF
the same, but the preview says “whole cabinet in mdf”
SHAKERLIFTTOEKICK
“no code”
the codes they say

The rule behind it: a bare number of 200 or more is a height; a smaller one is named instead of built (no cabinet is lower than 200 mm). In a stack bracket a number is that section's height, any size. A count no cabinet holds (720 SHELF) is the height: 720 mm with shelves.

NOTES THAT WORK

Several codes, one note.

Every code on this page is read by the add-in's own parser. Copy a note into a rectangle and build.

720MM 3 SHELF GOLA
  • 720 mm high
  • 3 shelves
  • Gola handle
UPPER 720MM 2 SHELF GLASS
  • Wall cabinet
  • 720 mm high
  • 2 shelves
  • Aluminium and glass doors
2565MM GOLA1700 SHAKER OAK TOEKICK100
  • 2565 mm tall unit
  • Gola grip line at 1700 mm
  • Shaker doors
  • Oak
  • 100 mm toe kick
SINK740 2 DOORS
  • Sink base
  • 740 mm bowl cutout
  • Two doors
STOVE750 OVEN600
  • Stove base
  • 750 mm hob cutout
  • 600 mm oven under the hob
(DRAWER 200)+(2 DOORS) SAGE
  • A 200 mm drawer over two doors
  • Sage fronts

One cabinet, or the whole shop?

A code changes one cabinet. Shop-wide defaults (board thicknesses, reveals, gola, door and face-frame sizes, banding, sheet stock and the default materials) live in the Shop Standard: Kerf, then Edit Shop Standard.